We service all Brands
Check out the features of our 23 point TUNE UP
Precision Furnace Tune-up Benefits:

Lower utility bills.
Extended equipment life.
Fewer repairs, breakdowns, and improved system reliability.
Peace of mind for you and your family.
Increased heating capacity.
Priority service scheduling.
HVACR Contractors License #2120949
Powered by Mountain Computers, Inc. Reno, NV Copyright © All Rights Reserved Total Refrigeration Service, Inc.
Designed by Mountain Marketing. Reno, NV Copyright © All Rights Reserved Total Refrigeration Service, Inc.
Click on the Maintenance Agreement below to download the full document. Feel free to fax into our office at anytime.
Maintenance Agreement
Precision Air-Conditioning Tune-up Benefits:

Lower utility bills by reducing energy consumption and waste.
Extended equipment life.
Peace of mind for you and your family.
Fewer repairs, and improved system reliability.
Increased cooling capacity and efficiency

Our Exclusive Precision Tune-Up Procedure Includes, As Needed:
1. Inspect and tighten all electrical connections and terminals.
2. Remove, clean, and adjust main gas burners.
3. Remove, clean, and adjust ignition/pilot assembly.
4. Thoroughly brush and vacuum clean the heat-exchanger(s) and combustion chambers.
5. Inspect heat-exchanger(s) & combustion chambers for cracks, rusting, or problem areas.
6. Vacuum out blower compartment; return airdrop, and surrounding area. (No duct cleaning)
7. Clean all return air grills throughout the home.
8. Inspect the flue assembly and test flue gas drafting mechanism.
9. Test and inspect all furnace safety controls.
10. Test, record, and adjust gas pressure.
11. Replace or clean standard air filters.
12. Remove and clean blower motor, drive mechanism and fan assembly.
13. Lubricate all fan motors and all moving parts.
14. Measure and adjust blower for correct airflow.
15. Adjust all dampers and set proper blower speed(s).
16. Clean, level, test, and calibrate thermostat.
17. Measure and record heating system output.
18. Inspect and test thermocouple output as well as pilot safety switch.
19. Measure and record electrical voltage, amperage, and component resistance.
20. Inspect and test all system transformers, relays, contactors, and controls. Measure performance
21. Repair minor air leaks in plenum and return airdrop.
22. Perform a complete and thorough, room-by-room, electronic carbon monoxide check of the entire house.
23. Advise customer on other ways to reduce energy consumption, improve safety and enhance comfort

1. Chemically clean and thoroughly wash condenser coil(s).
2. Thoroughly clean or replace standard air-filter(s).
3. Wash and level condensing unit for proper motor and bearing wear.
4. Lubricate motor and fan bearings as well as other moving parts as necessary.
5. Clean and inspect evaporator coil and drain pan when readily accessible.
6. Clean and inspect condensate drain lines and fittings.
7. Clean, level, and calibrate thermostat.
8. Adjust and thoroughly clean blower motor and fan assembly as needed.
9. Inspect, tighten and test all electrical connections. This includes disconnect switch.
10. Inspect all cooling system electrical wires, connectors, and terminals.
11. Test system starting and running capacitors.
12. Test all controls, switches, relays, transformers, contactors, motors, and fans.
13. Measure starting and running amperes, line voltage, and control voltage.
14. Test system-starting capabilities.
15. Test system for proper airflow and air delivery.
16. Inspect and adjust all safety controls.
17. Monitor refrigerant (Freon) pressures and temperatures.
18. Test and record super-heat and sub-cooling. Compare with factory specifications.
19. Adjust Freon metering control device per factory/manufactures recommendations.
20. Test and measure air-conditioning system for proper production and capacity.
21. Monitor fan motors and compressor operating temperatures.
22. Apply weather resistant protective coating to the outside unit. (Condenser)
23. Complete and present full written report.

Furnace
Air Conditioning
Online Service Request Form
Heating & Air Conditioning
Commercial Refrigeration
Ice Machines
Sales, Service & Rentals
Restaurant Equipment

24 HOUR
EMERGENCY SERVICE
(501) 794-1052
Main Phone: (501) 794-1052
Little Rock: 315-1355
Benton/Bryant: 778-9101
Fax: (501)794-1135

Regular Office Hours: 8am to 4:30pm